Make         

Model        

Year          

Transmission          Choose 1 Automatic Manual

Drive                     Choose 1 2 Wheel Drive 4 Wheel Drive

Size                       Choose 1 1/2 Ton 3/4 Ton 1 Ton Other

Modified       Choose 1 Lifted Lowered Standard

Inch Amount Modified       inches

Spec       Choose 1 1 Piece Driveshaft 2 Piece Driveshaft

Type       Choose 1 Aluminum Steel

Approx Horsepower      

* Please see How to Measure to correctly give dimension - Note: this link opens in a new window so data on this form is not lost

If modifying a driveshaft       Choose 1 New Lengthening Shortening

Select which Diagram was used: Diagram Diagram 1 Diagram 2 Diagram 5 Diagram 6 Diagram 7 Diagram 8 Diagram 9 Diagram 10

A.   Overall Length inches

B.   If Pinion Yoke has 2 Locating Tabs, measure between them using Figure B   Choose 1 or Skip to B1 3 7/32 3 5/8

B1. If Pinion Yoke does not have Locating Tabs, measure between the 2 Flat Surfaces in Figure B1

       inches

C.   T-400 and $l80 Trans ONLY...Output shaft is NOT T-400 or 4L80 Trans Threaded Not Threaded

D.   How far does Output Shaft stick out past end of Trans Case? Compress if necessary.  inches

E.   Is there Locating Tab on Pinion Yoke? Note: All 1350 series have tabs. Choose 1 Yes No

F.   What is U-Joint Cap Diameter that fits into Pinion Yoke? Choose 1 1 1/16 1 1/8 1 3/16

A.   Overall Length inches

B.    Ford 9 Inch ONLY : Measurement from base of threads on Pinion Shaft to front face of outer Pinion Bearing.

       See Figure B.   inches

B1. Ford 9 Inch ONLY : Pinion Support - bolted to front of housing, holds pinion seal  NOT Ford 9 Inch Aluminum Steel

C.   T-400 and 4L80 Trans Only...Output Shaft is NOT T-400 or 4L80 Trans Threaded Not Threaded

D.   How far does Output Shaft stick out past end of Trans Case? Compress if necessary. inches

A.   Overall Length inches

B.   If 4WD : What model name or number is Trans Case? 

       If 2WD : What model name or number is Transmission? 

B1. How many Splines on Output Shaft?

B2. How far does Output Shaft stick out past end of Trans Case? Compress if necessary. inches

C.   What is the Pilot Diameter at the Differential? inches

D.   What model name or number is the Differential?

A.   Pilot Diameter inches

B.   Locating Tab on Differential Yoke? Choose 1 Yes No

C.   U-Joint Cap Diameter that fits into Differential Yoke? Choose 1 1 1/16 1 1/8 1 3/16

D.   Overall Length inches

E.   What model name or number is the Differential?

F.   If 4WD : What model name or number is Trans Case? 

      If 2WD : What model name or number is Transmission? 

G.   How Wide is U-Joint at Differential? Measure U-Joints including Caps. Not Measuring U-Joint 3 7/32 3 5/8

       OR       Measure between tabs on Locating Tab Style Yoke Not Measuring U-Joint 3 7/32 3 5/8

       OR       GM or Dodge Yoke Without Locating Tabs inches

A1. Trans Case Yoke have Locating Tabs? Choose 1 Yes No

A2. Differential Yoke have Locating Tabs? Choose 1 Yes No

B1. U-Joint Cap Diameter that fits into Trans Case Yoke? Choose 1 1 1/16 1 1/8 1 3/16

B2. U-Joint Cap Diameter that fits into Trans Case Yoke? Choose 1 1 1/16 1 1/8 1 3/16

C.   Overall Length inches

D.  What model name or number is Differential?

E.   If 4WD : What model name or number is Trans Case? 

      If 2WD : What model name or number is Transmission? 

F1. How wide is U-Joint at Trans Case? Include Caps. Not Measuring U-Joint 3 7/32 3 5/8

F2. How wide is U-Joint at Trans Case? Include Caps. Not Measuring U-Joint 3 7/32 3 5/8

F3. Measure between tabs on Locating Tab Style Yoke. Not Measuring U-Joint 3 7/32 3 5/8

F4. GM or Dodge Yoke Without Locating Tabs

A.   Overall Length Front inches

B.   Overall Length Rear inches

C.   U-Joint Cap Diameter that fits into Pinion Yoke? Choose 1 1 1/16 1 1/8 1 3/16

D.   Pinion Yoke have Locating Tabs? Choose 1 Yes No

E1. T-400 or 4L80 Trans ONLY...Output Shaft is NOT T-400 or 4L80 Trans Threaded Not Threaded

E2. How far does Output Shaft stick out past end of Trans Case? Compress if necessary. inches

F.   How Wide is the Rear U-Joint including Caps? Not Measuring U-Joint 3 7/32 3 5/8

       OR       Measure between tabs on Locating Tab Style Pinion Yoke Not Measuring Tabbed Yoke 3 7/32 3 5/8

       OR       Measure across Pinion Yoke Without Locating Tabs inches

A.   Overall Length Front inches

B.   Overall Length Rear inches

C1. U-Joint Cap Diameter that fits into Trans Yoke? Choose 1 1 1/16 1 1/8 1 3/16

C2. U-Joint Cap Diameter that fits into Pinion Yoke? Choose 1 1 1/16 1 1/8 1 3/16

D1. Trans Yoke have Locating Tabs? Choose 1 Yes No

D2. Pinion Yoke have Locating Tabs? Choose 1 Yes No

E.   How Wide is the Front U-Joint including Caps? Not Measuring U-Joint 3 7/32 3 5/8

       OR       Measure between tabs on Locating Tab Style Yoke Not Measuring Tabbed Yoke 3 7/32 3 5/8

       OR       Measure across Pinion Yoke Without Locating Tabs inches

F.   How Wide is the Rear U-Joint including Caps? Not Measuring U-Joint 3 7/32 3 5/8

       OR       Measure between tabs on Locating Tab Style Yoke Not Measuring Tabbed Yoke 3 7/32 3 5/8

       OR       Measure across Pinion Yoke Without Locating Tabs inches

A.   Overall Length Front inches

B.   Overall Length Rear inches

C.   U-Joint Cap Diameter that fits into Pinion Yoke? Choose 1 1 1/16 1 1/8 1 3/16

D.   Pinion Yoke have Locating Tabs? Choose 1 Yes No

E.   T-400 or 4L80 Trans ONLY...Output Shaft is NOT T-400 or 4L80 Trans Threaded Not Threaded

F.   How far does Output Shaft stick out past end of Trans Case? inches

Contact Information

Name                   

Contact Phone      

Fax                

Email